Need Junk Yard Parts?

[kirksjeep]

I am headed back home to MD for Easter and I plan on hitting the pick and pull.  Last time I was there they had several XJ's and ZJ's and one almost stripped CJ7.  I am planning on trying to find a spare set of axle shafts, a 99+ intake manifold and a 99+ power steering pump.  If anyone needs something such as an air conditioning compressor for an OBA, spare axles shafts w or w/o unit bearings etc... let me know and I'll see what they have.  I am not planning on taking my trailer for large items like axles and stuff, but smaller items that fit in the Liberty ( or maybe the H3 ) I can get.  If you let me know specifically what you want I can try to give you a better idea of a price but here is an example of what I am thinking:

Dana 30 axle shafts w/o unit bearings $80
Dana 30 axle shafts w/ unit bearings $110
99+ intake manifold $60
Power steering pump 96+ $35
A/C compressor $50

[TJ777]

I'll give you money for a power steering pump for a 2000 tj sport my power steering leaks bad Ive been looking into rebuilding mine but if they are only 35 bucks ill just rebuild that one and replace the other. Let me know when you need the money by.

[PaulW]

2.5 TON ROCKWELLS??

[rocket]

drivers side power window swith/bezel (need the window swithces in it) form an 01-04 tacoma 4-door

[Seabee_BUC]

drivers side power window swith/bezel (need the window swithces in it) form an 01-04 tacoma 4-door

Is your child lock on again??? LOL 

[PaulW]

drivers side power window swith/bezel (need the window swithces in it) form an 01-04 tacoma 4-door

Is your child lock on again??? LOL 

i get beer caps jammed under mine

[rocket]

drivers side power window swith/bezel (need the window swithces in it) form an 01-04 tacoma 4-door

Is your child lock on again??? LOL 

no, i'll use the other two swiches for in cab winch control

[Seabee_BUC]

This site has nice pre-made ones and can do custom stuff too...This is where I got the one in JD's jeep

12 Volt Guy

[rocket]

seen them.  no good spot to mount one (and they would clash w/ my decor LOL).  I would wire the switches for the two rear windows to require both activated in the same direction to cause the winch to operate (and maybe put a isolation switch somewhere).

[PaulW]

seen them.  no good spot to mount one (and they would clash w/ my decor LOL).  I would wire the switches for the two rear windows to require both activated in the same direction to cause the winch to operate (and maybe put a isolation switch somewhere).

and leave the rear windows inop??

[rocket]

dude, no way in heck i would buy a 4-door!  makes your bed the size of a match box! at that point, its better to buy an SUV

[PaulW]

dude, no way in heck i would buy a 4-door!  makes your bed the size of a match box! at that point, its better to buy an SUV

ok well that makes mroe sense to use the switches then if its a 2 door.

[kirksjeep]

TJ777 sorry no power steering pumps for a 2000 TJ.  They didn't even have a 2000 or newer XJ that I could try and see if it would work. 

Jeremy also sorry no Tacoma's at all.  They only had one toyota and it was a mid 90's 4 runner. 

I wish I would have had my trailer, they have an 88 waggoner with Dana 44's.  They had a handful of XJ's, half of which were 2wd, and about half a dozen ZJ's and most were the V8's.  They also 3 CJ7, one had a full roll cage which looked like it was in good shape, but I couldn't tell.  It also had 2 good 33x12.50/15 BFG MT that would have made good spares. 

I picked up an intake manifold from a 99XJ ( only one they had) and the power steering pump that bolted up.  I also pulled the axle shafts out of a 98 XJ.  The passenger side shaft has a newer U-joint and they will make good spares.  I only paid $77 for all my stuff, but it took about 3 1/2 hours.  A lot of that time was just looking around and 20 minutes was waiting for the fork lift to lift the 98 XJ so I could pull the shafts.  I also managed to cut the plug for the 4wd switch from a 96 XJ. 

[PaulW]

TJ777 sorry no power steering pumps for a 2000 TJ.  They didn't even have a 2000 or newer XJ that I could try and see if it would work. 

Jeremy also sorry no Tacoma's at all.  They only had one toyota and it was a mid 90's 4 runner. 

I wish I would have had my trailer, they have an 88 waggoner with Dana 44's.  They had a handful of XJ's, half of which were 2wd, and about half a dozen ZJ's and most were the V8's.  They also 3 CJ7, one had a full roll cage which looked like it was in good shape, but I couldn't tell.  It also had 2 good 33x12.50/15 BFG MT that would have made good spares. 

I picked up an intake manifold from a 99XJ ( only one they had) and the power steering pump that bolted up.  I also pulled the axle shafts out of a 98 XJ.  The passenger side shaft has a newer U-joint and they will make good spares.  I only paid $77 for all my stuff, but it took about 3 1/2 hours.  A lot of that time was just looking around and 20 minutes was waiting for the fork lift to lift the 98 XJ so I could pull the shafts.  I also managed to cut the plug for the 4wd switch from a 96 XJ. 

you must be as happy as a redneck at the pink-n-pull....