JT4x4
The Mud Pit => Wrenching => Topic started by: Gr33NGoph3R on March 17, 2011, 03:47:26 PM
-
wondering if anyone has good measurements for skid plates (oil pan, engine ect) so I can make them myself and save some money I can figure it out but if anyone already has them it would be great
-
Do yourself a favor. First, decide what kind of skids your going to go with. If your thinking a belly up Flat (or mostly Flat) style skid, first things first. 1" motor mount lift!!! And while your at it, spring for the 1" body lift as well. Both of these will provide the clearance you are gonna need to slap some skids on the bottom of your frame. Once you have that done, go to wal-mart and get some poster board, scissors, tape, a sharpie, and a tape measure. Measure, tape, cut, draw.... you get the idea. Label them as you go and keep them until you get the metal your going to use. Use them as templates for what you cut on the metal. My suggestion, go 1/16" thicker than what everyone suggests so that you can counter sink the mounting holes to reduce the risk of shearing of a bolt head when you drag a rock. But i'd save your money and get that thing up higher off the ground and get some bigger meats on those studs.
-
i think for a you should run 1/8" steel and then use 1"x1" square stock to brace it. then use dimple dies to give it lots of strength this keeps it light, and will be stronger than throwing a massive piece of metal under ur rig, but i would agree that counter sinking your bolts it a good idea.
Now ur thinking 1/8 that seems thin well with it your going the dimple die route thats the thickest you can go. You can't dimple die metal any thicker than 1/8.
Now ur thinking dimple dies are expensive, so build your skid and mark where you want your holes then bring a case of beer over and ill make them dimply for you.
-
I like Nate's thinking, something like this.
(http://i597.photobucket.com/albums/tt60/Mr-Rock/Dsc03009.jpg)
(http://i597.photobucket.com/albums/tt60/Mr-Rock/Dsc03024.jpg)
I built my Flat skid out of 1/4" plate and it is heavy, making it a Bi*@# to remove! something like this.
(http://i597.photobucket.com/albums/tt60/Mr-Rock/Flatskid029.jpg)
-
i said screw building my own and bought this
http://undercoverfab.com/transfer-case-skid-plates/68-hd-transfer-case-skid-plate-jeep-wrangler-yj-extra-clearance-carbon.html
the shop was 45 minutes from where i was stationed in florida it is a beast of a skid bolted right in and i don't think i will turn it into a pretze llike my stock one was it is a heavy bastard but i like it and there is a 10% dicsount for jeep forum shiping will be expensive he quoted me $90 to get it to me
-
i think for a you should run 1/8" steel and then use 1"x1" square stock to brace it. then use dimple dies to give it lots of strength this keeps it light, and will be stronger than throwing a massive piece of metal under ur rig, but i would agree that counter sinking your bolts it a good idea.
Now ur thinking 1/8 that seems thin well with it your going the dimple die route thats the thickest you can go. You can't dimple die metal any thicker than 1/8.
Now ur thinking dimple dies are expensive, so build your skid and mark where you want your holes then bring a case of beer over and ill make them dimply for you.
What's your beer? So I know when the time comes
-
been looking around and based on steele prices and with the 1" motor mount and body lifts id be paying around the same price as one skid to cover the whole bottom of my jeep
-
Shop around, some companies sell a belly up "kit" that sometimes comes with the motor mount/body mount lift equipment.
-
Thx ill take a look