« previous next »
Pages: [1]   Go Down

Author Topic: WTB: Scrap steel to fabricate rear tow points  (Read 1557 times)

Offline smaug1911

  • Honorary Member
  • Rock Crawler
  • ***
  • Posts: 473
WTB: Scrap steel to fabricate rear tow points
« on: October 26, 2008, 05:24:43 AM »
Looking for some heavy duty steel that I could cut, drill, and weld to my bumper to make some good tow points. I'd like to put a shackle through it.

Anybody have something like that for free or cheap?
« Last Edit: October 26, 2008, 05:27:51 AM by smaug1911 »
Logged
97 V6 Tacoma TRD. 2.5" front coil spacers. 3.5' Downey leaf springs, 2" 4Crawler body Lift, rear Bilstein 5125's, 35" BFG KM2's, Skid row transfer skid, Ocean State Crawlers front winch bumper, custom rear bumper, Kajobuilt sliders, deckplate mod, grey wire mod, Smittybilt XRC8.

Offline Seabee_BUC

  • Honorary Member
  • Trail Master
  • ***
  • Posts: 1106
  • Yeah she's fast...Terrible in the rocks I'm sure!
Re: WTB: Scrap steel to fabricate rear tow points
« Reply #1 on: October 26, 2008, 03:52:37 PM »
Thickest I got is 1/4"...Not necessarily what you're looking for. I'd suspect you need something at least 1/2" or better...I think you can find them online for around 40 bucks though...
Logged

Offline smaug1911

  • Honorary Member
  • Rock Crawler
  • ***
  • Posts: 473
Re: WTB: Scrap steel to fabricate rear tow points
« Reply #2 on: October 26, 2008, 07:20:33 PM »
yeah...I'm just seeing what people have.

Theoretically, my bumper is an acceptable for towing, but I would like something better.
Logged
97 V6 Tacoma TRD. 2.5" front coil spacers. 3.5' Downey leaf springs, 2" 4Crawler body Lift, rear Bilstein 5125's, 35" BFG KM2's, Skid row transfer skid, Ocean State Crawlers front winch bumper, custom rear bumper, Kajobuilt sliders, deckplate mod, grey wire mod, Smittybilt XRC8.

Offline moosin

  • Trail Boss
  • Trail Master
  • ****
  • Posts: 1281
Re: WTB: Scrap steel to fabricate rear tow points
« Reply #3 on: October 27, 2008, 01:43:44 AM »
ah shoot let me look at the end of the steel i got for the R.T.I. ramp i think those same slugs of steel i was telling you about at the cruise day are in the ends of them. sorry bout that just now thought of it ill look tommorrow when its light.
Logged

jmwendler

  • Guest
Re: WTB: Scrap steel to fabricate rear tow points
« Reply #4 on: October 27, 2008, 03:24:10 AM »
I have some 1/2x2 and 1/2x4 flat bar that should work pretty well. About how much do you think you need?
Logged

Offline rocket

  • Trail Master
  • *****
  • Posts: 2802
  • That is what i call, "Flexing"
    • my webshots photo site - lots of wheeling pics!
Re: WTB: Scrap steel to fabricate rear tow points
« Reply #5 on: October 27, 2008, 03:32:15 AM »
Quote from: jmwendler on October 27, 2008, 03:24:10 AM
I have some 1/2x2 and 1/2x4 flat bar that should work pretty well. About how much do you think you need?

if you are offloading it, i'll take some for "Project Rear Bumper"
Logged
1973 Chevy El Camino: 383 sb, lots of power
2004 Toyota Tacoma TRD 3.4L xtra cab 2.5" skyjacker coilovers/leafs, 32x11.5-15" Super Swamper TSL/SXs, Bent-up front bumper, smittybilt winch, 4xInovations sliders, Bud-built skids, custom rear bumper/light bar, hella lights, "custom" body work

Offline smaug1911

  • Honorary Member
  • Rock Crawler
  • ***
  • Posts: 473
Re: WTB: Scrap steel to fabricate rear tow points
« Reply #6 on: October 27, 2008, 04:53:27 AM »
I am looking to make something either 3/4 or 1inch in thickness.

may just end up ordering a piece.
Logged
97 V6 Tacoma TRD. 2.5" front coil spacers. 3.5' Downey leaf springs, 2" 4Crawler body Lift, rear Bilstein 5125's, 35" BFG KM2's, Skid row transfer skid, Ocean State Crawlers front winch bumper, custom rear bumper, Kajobuilt sliders, deckplate mod, grey wire mod, Smittybilt XRC8.

Offline moosin

  • Trail Boss
  • Trail Master
  • ****
  • Posts: 1281
Re: WTB: Scrap steel to fabricate rear tow points
« Reply #7 on: October 28, 2008, 10:16:03 PM »
sorry took so long i looked last night. they are 1" thick i think 3" wide and about 3" long they would have been perfect except for the 3/4" hole drilled across the middle of them on the wide part. well i tried sorry.
Logged
Pages: [1]   Go Up
« previous next »