« previous next »
Pages: [1]   Go Down

Author Topic: Setting timing and Carb  (Read 2569 times)

Offline JSchwinn

  • Trail Queen
  • **
  • Posts: 76
Setting timing and Carb
« on: October 26, 2015, 11:25:53 PM »
Hey guys I need a huge favor.... I just changed out the engine in my J10 and have 0 clue how to set the timing and carb....  I took the #1 plug out and turn the engine by hand till I feel the compression, set it to true dead center and set the dizzy to the #1 plug.  When I turned the engine over is backfired into the carb... assumed it was out 180 so i took the dizzy out and turned the engine over 360 and still no luck....  I'm in a time crunch bc Im using the truck in my engagement photos this sunday.... can some please come help me in Gales Ferry this week.... will to buy pizza and beer
« Last Edit: October 27, 2015, 12:22:02 PM by JSchwinn »
Logged
1993 YJ - I6 - 4" RC Lift - 8k Winch - 33's

Offline Big Chuck

  • President
  • Trail Master
  • *****
  • Posts: 730
Re: Setting timing and Carb
« Reply #1 on: October 27, 2015, 03:10:48 AM »
360 engine? Turn the dizzy 180?
Logged
Tube chassis, 5.3LS, Ford Dana 60 Chevy 14 Bolt 5.13 gears. 203/205 doubler, Hydro steering, air shocks, 42 inch Iroks on 16.5 H1 double bead locks.

Offline JSchwinn

  • Trail Queen
  • **
  • Posts: 76
Re: Setting timing and Carb
« Reply #2 on: October 27, 2015, 12:22:54 PM »
With the vacuum port it really can only sit where it is. 
Logged
1993 YJ - I6 - 4" RC Lift - 8k Winch - 33's

Offline skibum

  • Paid Members
  • Trail Master
  • ***
  • Posts: 869
Re: Setting timing and Carb
« Reply #3 on: October 27, 2015, 12:58:38 PM »
Make sure firing order if correct
Logged
09 Rubi 4Dr,Compleat Heavy Duty Polly Performance skid plate system,Kilby Evap Relocation kit,Rampage front bumper,Swaybar motor flip,Clayton 3.5in lift w/steering corection kit,35in GY MTR's on 15in MB Wheels,Ace Enginering Rear Bumper W/Tire carrier,Prorock D44 Front axel,5.13s,cromo rear shafts

Offline JSchwinn

  • Trail Queen
  • **
  • Posts: 76
Re: Setting timing and Carb
« Reply #4 on: October 27, 2015, 01:44:16 PM »
double and triple checked.... I honestly just need an extra hand that has more knowledge than me to get this sucker going.... tonight im going to put a cork into the #1 plug and turn the engine till it pops and adjust the dizzy to the #1 plug.
Logged
1993 YJ - I6 - 4" RC Lift - 8k Winch - 33's

Offline calvynandhobbs

  • Honorary Member
  • Trail Master
  • ***
  • Posts: 3087
Re: Setting timing and Carb
« Reply #5 on: October 27, 2015, 02:14:13 PM »
I don't know much about carbs and getting them set, otherwise I'd try to stop by to help you. I can't even get the carb on my moped to play nice anymore and it's supposedly simple.
Logged
1994 YJ on 37s

Offline JSchwinn

  • Trail Queen
  • **
  • Posts: 76
Re: Setting timing and Carb
« Reply #6 on: October 28, 2015, 12:40:10 PM »
timing is now set and engine is running well. thanks guys
Logged
1993 YJ - I6 - 4" RC Lift - 8k Winch - 33's

Offline Big Chuck

  • President
  • Trail Master
  • *****
  • Posts: 730
Re: Setting timing and Carb
« Reply #7 on: October 28, 2015, 01:29:21 PM »
What did you end up doing?
Logged
Tube chassis, 5.3LS, Ford Dana 60 Chevy 14 Bolt 5.13 gears. 203/205 doubler, Hydro steering, air shocks, 42 inch Iroks on 16.5 H1 double bead locks.

Offline JSchwinn

  • Trail Queen
  • **
  • Posts: 76
Re: Setting timing and Carb
« Reply #8 on: October 28, 2015, 03:35:03 PM »
followed the directions lol, I wasn't using the right mark on the balancer so timing was too far advanced.  The method I used was to remove the #1 plug and put a napkin over the hole and turned the engine by hand.  During the compression stroke the napkin was shot out and the mark on the balancer was right about at TDC so I put it to TDC installed the dizzy to the #1 plug and it was close enough to get it running and I adjusted it by hand till it ran well. 

Of course because nothing is ever easy I went to press the clutch down the pivot ball and spring decided to fall out....  so now I am pulling the tranny to set them back in place..... not very happy
Logged
1993 YJ - I6 - 4" RC Lift - 8k Winch - 33's

Offline Mr Rock

  • Administrator
  • Trail Master
  • *****
  • Posts: 1571
Re: Setting timing and Carb
« Reply #9 on: October 28, 2015, 06:55:52 PM »
Glad you got it running but bummer on the clutch fork!
Logged
'89, 4.2, NUTTERED, Team Rush, 4" Lift, 1" BL, 1" MML & HD shackles , Flat Belly Skid, SYE, 36 x 13.50s
XRC8, 150w KC's, Herculined, Tauras Elec Fan, Dual Batteries, Aussie in front, 8.8, TJ flares & Spool in rear, topless all of the time!
Pages: [1]   Go Up
« previous next »