« previous next »
Pages: [1]   Go Down

Author Topic: cad gone bad  (Read 1592 times)

Offline gearhead1985B

  • Honorary Member
  • Trail Master
  • ***
  • Posts: 882
  • the Snozberries taste like Snozberries
cad gone bad
« on: October 15, 2009, 01:31:15 AM »
today my jeep 4x4 indicator was coming on randomly so i think the cad on my jeep is going bad so i decided to replace it with a axle out me a cherokee is theres any thing else i need to put it in
Logged
"If you can read this, Thank a Teacher, if you can read it in English, thank a SOLDIER"

https://www.masterpull.com/Index.aspx
http://www.taboocustoms.com/

PaulW

  • Guest
Re: cad gone bad
« Reply #1 on: October 15, 2009, 01:31:52 AM »
Inner axle seal.
Logged

Offline kirksjeep

  • Honorary Member
  • Trail Master
  • ***
  • Posts: 1267
  • It's hip to be square (headlights) !
Re: cad gone bad
« Reply #2 on: October 15, 2009, 02:40:57 AM »
It might be the vacuum switch on the T-case.  It also could be a short in the wires. The fork in the CAD acts as a ground for the elecrical switch.  The most comon failure is the miles of vacuum lines going from the engine to the T-case and then up to the front axle. 

Even better, swap out the shafts for some out of a 96+ XJ or TJ and do away with the CAD and get the bigger U-joints.
Logged
1992 YJ Sahara, 4.5 Rubicon Express ED Lift, 35" BFG MT, Custom Bumpers, SYE/CV Drive Shaft, OBA, Ford 8.8 rear, 4.10 gears, tie rod flip, 1"MML/BL
2002 KJ Liberty, 2" Lift, 31" tires/DD
2002 F-150 Harley Davidson 5.4L SC
2013 Explorer Sport
2006 Harley Road King Classic
1988 Honda Hawk GT

Offline BlacXJeep

  • Honorary Member
  • Trail Master
  • ***
  • Posts: 1464
    • My Webshots
Re: cad gone bad
« Reply #3 on: October 15, 2009, 07:02:30 AM »
he was talking about doing that all weekend
Logged
Andy Doucette - A.K.A.(Douce)
W.O.J.

Offline gearhead1985B

  • Honorary Member
  • Trail Master
  • ***
  • Posts: 882
  • the Snozberries taste like Snozberries
Re: cad gone bad
« Reply #4 on: October 15, 2009, 09:35:26 PM »
yes i am going to swap out the shafts and seal this saturday and i am getting a brake booster out of a 95 and some 33's :P
Logged
"If you can read this, Thank a Teacher, if you can read it in English, thank a SOLDIER"

https://www.masterpull.com/Index.aspx
http://www.taboocustoms.com/

Offline BlacXJeep

  • Honorary Member
  • Trail Master
  • ***
  • Posts: 1464
    • My Webshots
Re: cad gone bad
« Reply #5 on: October 15, 2009, 09:51:06 PM »
 ;D
Logged
Andy Doucette - A.K.A.(Douce)
W.O.J.

PaulW

  • Guest
Re: cad gone bad
« Reply #6 on: October 16, 2009, 02:23:34 AM »
Let  me   have the old tires
Logged

Offline gearhead1985B

  • Honorary Member
  • Trail Master
  • ***
  • Posts: 882
  • the Snozberries taste like Snozberries
Re: cad gone bad
« Reply #7 on: October 16, 2009, 03:29:29 AM »
sorry paul i am trading them for the 33's
Logged
"If you can read this, Thank a Teacher, if you can read it in English, thank a SOLDIER"

https://www.masterpull.com/Index.aspx
http://www.taboocustoms.com/

PaulW

  • Guest
Re: cad gone bad
« Reply #8 on: October 17, 2009, 01:16:16 AM »
Ive done that swap before.  its easy, but may require seal modification to  make it work.  call me if you need a hand.
Logged

Offline gearhead1985B

  • Honorary Member
  • Trail Master
  • ***
  • Posts: 882
  • the Snozberries taste like Snozberries
Re: cad gone bad
« Reply #9 on: October 17, 2009, 03:09:59 AM »
What mod may be required
Logged
"If you can read this, Thank a Teacher, if you can read it in English, thank a SOLDIER"

https://www.masterpull.com/Index.aspx
http://www.taboocustoms.com/

PaulW

  • Guest
Re: cad gone bad
« Reply #10 on: October 17, 2009, 04:43:53 AM »
the housing was from an 84 4cyl and was going into an 89. no prob but motor trans and tcase were from a 94. no vaccum system.  bought a seal for a 94 pulled the carrier out and it turns out that the seal is larger then the boss where you would put the seal in.  the seal had a metal outer layer on it when cut off it became a perfect fit and w
Logged

PaulW

  • Guest
Re: cad gone bad
« Reply #11 on: October 17, 2009, 04:45:43 AM »
Worked as it should.  mine were  xjs, but it should b the same on urs
Logged
Pages: [1]   Go Up
« previous next »