« previous next »
Pages: [1]   Go Down

Author Topic: dana 35  (Read 1364 times)

Offline gearhead1985B

  • Honorary Member
  • Trail Master
  • ***
  • Posts: 882
  • the Snozberries taste like Snozberries
dana 35
« on: October 07, 2009, 10:13:35 PM »
I am trying to remove an axle shaft from a dana 35 non c clip and i have unbolted everything and removed the spiders and the axle will not come out am i missing something  this is on a 2002 grand cherokee with rear disc
Logged
"If you can read this, Thank a Teacher, if you can read it in English, thank a SOLDIER"

https://www.masterpull.com/Index.aspx
http://www.taboocustoms.com/

Offline calvynandhobbs

  • Honorary Member
  • Trail Master
  • ***
  • Posts: 3087
Re: dana 35
« Reply #1 on: October 07, 2009, 10:40:27 PM »
I don't think non c-clip D35s were used after 1990 or 1991. When I removed shafts in my D44 it was very difficult to get them to budge. It took a couple hits with a hammer to break them free and then they slid out, but I would double check for c-clips if I were you.
Logged
1994 YJ on 37s

Offline gearhead1985B

  • Honorary Member
  • Trail Master
  • ***
  • Posts: 882
  • the Snozberries taste like Snozberries
Re: dana 35
« Reply #2 on: October 07, 2009, 11:01:03 PM »
I have the spider gears out there were no c clips so do i go at it with a slide hammer on the wheel mounting flange
Logged
"If you can read this, Thank a Teacher, if you can read it in English, thank a SOLDIER"

https://www.masterpull.com/Index.aspx
http://www.taboocustoms.com/

Offline kirksjeep

  • Honorary Member
  • Trail Master
  • ***
  • Posts: 1267
  • It's hip to be square (headlights) !
Re: dana 35
« Reply #3 on: October 08, 2009, 02:36:09 AM »
Dana 35's were never made with disc brakes, sounds like the crappy D44 that came with the GC's.  I am guessing you pulled the discs and the bolts that hold the axle shafts in place.
Logged
1992 YJ Sahara, 4.5 Rubicon Express ED Lift, 35" BFG MT, Custom Bumpers, SYE/CV Drive Shaft, OBA, Ford 8.8 rear, 4.10 gears, tie rod flip, 1"MML/BL
2002 KJ Liberty, 2" Lift, 31" tires/DD
2002 F-150 Harley Davidson 5.4L SC
2013 Explorer Sport
2006 Harley Road King Classic
1988 Honda Hawk GT

Offline calvynandhobbs

  • Honorary Member
  • Trail Master
  • ***
  • Posts: 3087
Re: dana 35
« Reply #4 on: October 08, 2009, 02:49:22 AM »
Quote from: kirksjeep on October 08, 2009, 02:36:09 AM
Dana 35's were never made with disc brakes, sounds like the crappy D44 that came with the GC's.  I am guessing you pulled the discs and the bolts that hold the axle shafts in place.

That's what I'm thinking. You probably have a D44a, which is aluminum.
Logged
1994 YJ on 37s

Offline gearhead1985B

  • Honorary Member
  • Trail Master
  • ***
  • Posts: 882
  • the Snozberries taste like Snozberries
Re: dana 35
« Reply #5 on: October 08, 2009, 03:21:39 AM »
The cover looks idenical to my 35
Logged
"If you can read this, Thank a Teacher, if you can read it in English, thank a SOLDIER"

https://www.masterpull.com/Index.aspx
http://www.taboocustoms.com/

PaulW

  • Guest
Re: dana 35
« Reply #6 on: October 08, 2009, 01:56:17 PM »
Napa listed 2 options for the rear axle when I went there last night, spicer 35 and 44.  There were 2 bearings in each box, and they had the same part num for each axle.  Sucks that the wheel bearing went out in your jeep and you werent able to  get out to here to use the press.  Good luck with both repairs.
Logged
Pages: [1]   Go Up
« previous next »