Author Topic: Ball joint advice  (Read 3795 times)

Offline phoenix

  • Mudd Hog
  • ***
  • Posts: 136
Ball joint advice
« on: February 28, 2009, 12:00:38 PM »
Quick tip for everyone.

If you are changing ball joints on a 83 gmc an you are trying to get the old ones out. (press in)  After beating on one for a few min because they won't move, TRY GOING THE OTHER WAY!! 2 friggen hours later,when I finally smartened up, it took about 30 seconds to pop out! >:( :( :o ??? ::) :P :-[ :-X :-\

PaulW

  • Guest
Re: Ball joint advice
« Reply #1 on: February 28, 2009, 01:15:59 PM »
Quick tip for everyone.

If you are changing ball joints on a 83 gmc an you are trying to get the old ones out. (press in)  After beating on one for a few min because they won't move, TRY GOING THE OTHER WAY!! 2 friggen hours later,when I finally smartened up, it took about 30 seconds to pop out! >:( :( :o ??? ::) :P :-[ :-X :-\

DOH!

Offline Axle

  • Honorary Member
  • Trail Master
  • ***
  • Posts: 2008
  • Merica!!!
Re: Ball joint advice
« Reply #2 on: February 28, 2009, 02:16:45 PM »
Ouch...  At least it went quick when you figured it out!  ;)
Axle:  2
Nemesis: 1

I win!

Offline phoenix

  • Mudd Hog
  • ***
  • Posts: 136
Re: Ball joint advice
« Reply #3 on: February 28, 2009, 03:24:58 PM »

DOH!
Not QUITE what I said, but close! Now I just got to go get the new ones pressed in.

PaulW

  • Guest
Re: Ball joint advice
« Reply #4 on: February 28, 2009, 04:54:15 PM »

DOH!
Not QUITE what I said, but close! Now I just got to go get the new ones pressed in.

I have the OTC ball joint master kit if you want to use it. 

Offline rocket

  • Trail Master
  • *****
  • Posts: 2802
  • That is what i call, "Flexing"
    • my webshots photo site - lots of wheeling pics!
Re: Ball joint advice
« Reply #5 on: February 28, 2009, 05:31:32 PM »
the haynes manual didn't specify which way to push?
1973 Chevy El Camino: 383 sb, lots of power
2004 Toyota Tacoma TRD 3.4L xtra cab 2.5" skyjacker coilovers/leafs, 32x11.5-15" Super Swamper TSL/SXs, Bent-up front bumper, smittybilt winch, 4xInovations sliders, Bud-built skids, custom rear bumper/light bar, hella lights, "custom" body work

PaulW

  • Guest
Re: Ball joint advice
« Reply #6 on: February 28, 2009, 06:50:17 PM »
the haynes manual didn't specify which way to push?


hehe that sounds dirty :D

Offline phoenix

  • Mudd Hog
  • ***
  • Posts: 136
Re: Ball joint advice
« Reply #7 on: March 01, 2009, 01:19:54 AM »

I have the OTC ball joint master kit if you want to use it. 
Can you explain a bit? Is this to install, remove, or both? Heck, you are close enough for me to take a ride! lol

the haynes manual didn't specify which way to push?

No, just says to push till it was in. ;D ;D ;D

PaulW

  • Guest
Re: Ball joint advice
« Reply #8 on: March 01, 2009, 01:37:44 PM »

I have the OTC ball joint master kit if you want to use it. 
Can you explain a bit? Is this to install, remove, or both? Heck, you are close enough for me to take a ride! lol

the haynes manual didn't specify which way to push?

No, just says to push till it was in. ;D ;D ;D

It installs, and removes ball joints in pretty much every application that uses pressed in ball joints.  GM FORD CHRYSLER, Mercedes, all of them.  Need to use it pm me.  My toolbox is in storage at a friends house in Cromwell, so I'd just have to run over and grab it for ya.  I even have the instructions still on how to use it if it'll help.

Offline phoenix

  • Mudd Hog
  • ***
  • Posts: 136
Re: Ball joint advice
« Reply #9 on: March 02, 2009, 10:57:12 AM »
Cool, will let you know in a couple days.

PaulW

  • Guest
Re: Ball joint advice
« Reply #10 on: March 02, 2009, 01:28:24 PM »
Cool, will let you know in a couple days.

No problem, I'll grab the press and leave it in my trunk so we can meet up.

Offline phoenix

  • Mudd Hog
  • ***
  • Posts: 136
Re: Ball joint advice
« Reply #11 on: March 03, 2009, 12:25:48 AM »
SWEET!! 2 q's, how long does it take to do, and do you get out to waterbury much?

PaulW

  • Guest
Re: Ball joint advice
« Reply #12 on: March 03, 2009, 02:28:43 PM »
SWEET!! 2 q's, how long does it take to do, and do you get out to waterbury much?

I'm in waterbury about 4 times if not more per week.  pressing in the ball joints takes about 5 min with air and an impact gun.  a big friggin ratchet would work, but takes forever!

Offline phoenix

  • Mudd Hog
  • ***
  • Posts: 136
Re: Ball joint advice
« Reply #13 on: March 03, 2009, 09:58:24 PM »
You got a pm!! ;D

PaulW

  • Guest
Re: Ball joint advice
« Reply #14 on: March 03, 2009, 11:16:57 PM »