« previous next »
Pages: [1] 2   Go Down

Author Topic: 99 Explorer 8.8 rear  (Read 4577 times)

Offline Big Chuck

  • President
  • Trail Master
  • *****
  • Posts: 731
99 Explorer 8.8 rear
« on: February 23, 2015, 07:12:23 PM »
Well Alright, I finally picked up my new rear diff from a 99 Explorer, 4.10 open. I have a 4.10 dana 30 almost ready for install. I am getting ready to order Calipers and Swap kit from ECGS along with a 1330 flange adapter. Now if the weather would get better and my garage would get bigger we would be all set LOL.
Chuck
Logged
Tube chassis, 5.3LS, Ford Dana 60 Chevy 14 Bolt 5.13 gears. 203/205 doubler, Hydro steering, air shocks, 42 inch Iroks on 16.5 H1 double bead locks.

Offline Mr Rock

  • Administrator
  • Trail Master
  • *****
  • Posts: 1571
Re: 99 Explorer 8.8 rear
« Reply #1 on: February 23, 2015, 10:34:06 PM »
Did you weld the tubes to the center section yet? if you are ordering from ECGS you should pick up a spartan locker from them too!
Logged
'89, 4.2, NUTTERED, Team Rush, 4" Lift, 1" BL, 1" MML & HD shackles , Flat Belly Skid, SYE, 36 x 13.50s
XRC8, 150w KC's, Herculined, Tauras Elec Fan, Dual Batteries, Aussie in front, 8.8, TJ flares & Spool in rear, topless all of the time!

Offline Big Chuck

  • President
  • Trail Master
  • *****
  • Posts: 731
Re: 99 Explorer 8.8 rear
« Reply #2 on: February 24, 2015, 01:24:43 AM »
I haven't done a thing to it yet.
Logged
Tube chassis, 5.3LS, Ford Dana 60 Chevy 14 Bolt 5.13 gears. 203/205 doubler, Hydro steering, air shocks, 42 inch Iroks on 16.5 H1 double bead locks.

Offline JSchwinn

  • Trail Queen
  • **
  • Posts: 76
Re: 99 Explorer 8.8 rear
« Reply #3 on: February 24, 2015, 03:31:26 PM »
You should make your garage big enough so we can fit my jeep and do it at the same time lol
Logged
1993 YJ - I6 - 4" RC Lift - 8k Winch - 33's

Offline Mreecew

  • Rock Crawler
  • ****
  • Posts: 256
  • Bonzai Samurai!!!!
Re: 99 Explorer 8.8 rear
« Reply #4 on: February 25, 2015, 08:14:15 PM »
Good job, make sure you weld the tubes, get a locker and a SOLID dif cover, then all you need is to attend a "drive like rock" training session. Also before you put the 30 in make up some C gussets like rocks yj and my fathers yj have, also 97+ shafts would be worth putting in so you don't have to worry as much.
Logged
1991 Samurai, 1.3 TBI, 35" KM2's, full 2 1/4" exhaust, SOA, RUF, Trail Tough Belly Skid, 5k Winch, Locked front and rear, GRS-2 transfer case gears (4.89:1 low), Built front axle with trusses, guards, gussets and birfield rings, Shrockworks gas tank skid, junk body and not much of a top.

Offline Big Chuck

  • President
  • Trail Master
  • *****
  • Posts: 731
Re: 99 Explorer 8.8 rear
« Reply #5 on: February 25, 2015, 09:45:54 PM »
You have a pic of the C-gussets you speak of?????
Logged
Tube chassis, 5.3LS, Ford Dana 60 Chevy 14 Bolt 5.13 gears. 203/205 doubler, Hydro steering, air shocks, 42 inch Iroks on 16.5 H1 double bead locks.

Offline Big Chuck

  • President
  • Trail Master
  • *****
  • Posts: 731
Re: 99 Explorer 8.8 rear
« Reply #6 on: March 24, 2015, 08:19:06 PM »
Ok so I finally just ordered my Barnes 4WD 8.8 install kit with a nice little 10% discount. Ed and I cut the old brackets and such off 2 weeks ago and cleaned the tubes up. I have an Aussie locker ready to be installed in that bad larry. Ordering the Solid Diff cover also in a few minutes.
Logged
Tube chassis, 5.3LS, Ford Dana 60 Chevy 14 Bolt 5.13 gears. 203/205 doubler, Hydro steering, air shocks, 42 inch Iroks on 16.5 H1 double bead locks.

Offline JSchwinn

  • Trail Queen
  • **
  • Posts: 76
Re: 99 Explorer 8.8 rear
« Reply #7 on: March 26, 2015, 02:51:23 PM »
Chuck, as you know I'm in the same boat as your right now with the swap.  What made you decide on the Aussie locker?  I have a non selectable in the Dana 30 I'm installing so I'm thinking I mine as well do the Aussie but have hear bad reviews about non-selectable.
Logged
1993 YJ - I6 - 4" RC Lift - 8k Winch - 33's

Offline Big Chuck

  • President
  • Trail Master
  • *****
  • Posts: 731
Re: 99 Explorer 8.8 rear
« Reply #8 on: March 26, 2015, 03:07:44 PM »
I have heard good things about lunchbox type lockers, and I have seen Rock's in action. Take a look at the video's and testimonials on the Lokka website. I do believe there are a few guys here in the club that run these type of lockers and are happy with them. Do you have your 8.8 all cleaned up and ready to go?
Chuck
Logged
Tube chassis, 5.3LS, Ford Dana 60 Chevy 14 Bolt 5.13 gears. 203/205 doubler, Hydro steering, air shocks, 42 inch Iroks on 16.5 H1 double bead locks.

Offline skibum

  • Paid Members
  • Trail Master
  • ***
  • Posts: 869
Re: 99 Explorer 8.8 rear
« Reply #9 on: March 26, 2015, 06:05:28 PM »
They do make noise and sometimes lock on road when turning. What makes them good is there cheep. E lockers and ARB"s are the best but very expensive. If u can deal with the small issues that auto lockers do then u will be fine. Off road an auto locker is very tough and perform as well as selectables.
Logged
09 Rubi 4Dr,Compleat Heavy Duty Polly Performance skid plate system,Kilby Evap Relocation kit,Rampage front bumper,Swaybar motor flip,Clayton 3.5in lift w/steering corection kit,35in GY MTR's on 15in MB Wheels,Ace Enginering Rear Bumper W/Tire carrier,Prorock D44 Front axel,5.13s,cromo rear shafts

Offline calvynandhobbs

  • Honorary Member
  • Trail Master
  • ***
  • Posts: 3087
Re: 99 Explorer 8.8 rear
« Reply #10 on: March 26, 2015, 06:41:16 PM »
I agree with what Bob said above. If I could afford only one selectable it would be for the front axle. I've never had a problem with the rear axle with Detroits or Aussies, but an auto locker in the front can be very unpredictable when using 4x4 on a snowy road. The tires need to have a little traction in order to ratchet and differentiate and I have had then lock in the middle of a turn in the past, which makes you continue going straight.
Logged
1994 YJ on 37s

Offline JSchwinn

  • Trail Queen
  • **
  • Posts: 76
Re: 99 Explorer 8.8 rear
« Reply #11 on: March 26, 2015, 06:48:31 PM »
Alright, good to know.  My front already has an auto locker.  I'll most likely be going to an auto for the rear.  My 8.8 is almost ready to go, just need to finish cleaning it up.  I'll do a locker before the install though and am still not really in a rush
Logged
1993 YJ - I6 - 4" RC Lift - 8k Winch - 33's

Offline HOT-ROD

  • Trail Master
  • *****
  • Posts: 2190
Re: 99 Explorer 8.8 rear
« Reply #12 on: April 01, 2015, 12:30:10 AM »
i love the detroit in the rear and the lockrite in the front. super tough!!
Logged

Offline Big Chuck

  • President
  • Trail Master
  • *****
  • Posts: 731
Re: 99 Explorer 8.8 rear
« Reply #13 on: April 15, 2015, 06:46:11 PM »
Ok so I just ordered a Lokka dana 30 locker and already have the Aussie 8.8 locker ready to be installed. Now I just need to find a bigger garage and a lift would help LOL.
Logged
Tube chassis, 5.3LS, Ford Dana 60 Chevy 14 Bolt 5.13 gears. 203/205 doubler, Hydro steering, air shocks, 42 inch Iroks on 16.5 H1 double bead locks.

Offline calvynandhobbs

  • Honorary Member
  • Trail Master
  • ***
  • Posts: 3087
Re: 99 Explorer 8.8 rear
« Reply #14 on: April 15, 2015, 07:43:27 PM »
Way to go Chuck. You'll enjoy it. I have the garage and no time. I need to find time. Just as a side note, I'm picking up an ARB and front diff cover tonight. Both previously purchased, but NIB.
Logged
1994 YJ on 37s
Pages: [1] 2   Go Up
« previous next »