« previous next »
Pages: 1 [2]   Go Down

Author Topic: New Engine  (Read 3413 times)

Offline Big Chuck

  • President
  • Trail Master
  • *****
  • Posts: 731
Re: New Engine
« Reply #15 on: May 28, 2015, 03:46:29 PM »
Did you use a new flywheel or one that was on the engine?
Chuck
Logged
Tube chassis, 5.3LS, Ford Dana 60 Chevy 14 Bolt 5.13 gears. 203/205 doubler, Hydro steering, air shocks, 42 inch Iroks on 16.5 H1 double bead locks.

Offline skibum

  • Paid Members
  • Trail Master
  • ***
  • Posts: 869
Re: New Engine
« Reply #16 on: May 28, 2015, 06:04:48 PM »
TOB should not be reasting on pressure plate forks. Will wear out TOB faster. Dont buy a ford
Logged
09 Rubi 4Dr,Compleat Heavy Duty Polly Performance skid plate system,Kilby Evap Relocation kit,Rampage front bumper,Swaybar motor flip,Clayton 3.5in lift w/steering corection kit,35in GY MTR's on 15in MB Wheels,Ace Enginering Rear Bumper W/Tire carrier,Prorock D44 Front axel,5.13s,cromo rear shafts

Offline JSchwinn

  • Trail Queen
  • **
  • Posts: 76
Re: New Engine
« Reply #17 on: May 29, 2015, 03:46:11 PM »
Yea I assumed it was the TOB, its just strange it didn't make the noise with the old engine.  Next meeting I'll have to get everyones input hearing the noise in person.  Also when I disengage the clutch while in gear I can kind of hear what sounds like the clutch rubbing the flywheel?

I used the flywheel from the new engine
Logged
1993 YJ - I6 - 4" RC Lift - 8k Winch - 33's

Offline Big Chuck

  • President
  • Trail Master
  • *****
  • Posts: 731
Re: New Engine
« Reply #18 on: May 29, 2015, 04:03:38 PM »
How many miles have you put on it since the swap? Could just be rust and junk on the flywheel that needs to get kicked off after some driving...
Logged
Tube chassis, 5.3LS, Ford Dana 60 Chevy 14 Bolt 5.13 gears. 203/205 doubler, Hydro steering, air shocks, 42 inch Iroks on 16.5 H1 double bead locks.

Offline JSchwinn

  • Trail Queen
  • **
  • Posts: 76
Re: New Engine
« Reply #19 on: May 29, 2015, 07:41:02 PM »
good point, that was kind of my thought.  Haven't put more than 20-30 miles on it.  Need to replace the rear u-joint for the 4th time.....
Logged
1993 YJ - I6 - 4" RC Lift - 8k Winch - 33's

Offline Big Chuck

  • President
  • Trail Master
  • *****
  • Posts: 731
Re: New Engine
« Reply #20 on: May 29, 2015, 08:27:13 PM »
Yeah, do some driving kick the dust off all of those moving parts and you should be ok. Why is your U-Joint bad again? That seems kind of strange, you don't have that many miles on it since you bought it.....
Logged
Tube chassis, 5.3LS, Ford Dana 60 Chevy 14 Bolt 5.13 gears. 203/205 doubler, Hydro steering, air shocks, 42 inch Iroks on 16.5 H1 double bead locks.

Offline JSchwinn

  • Trail Queen
  • **
  • Posts: 76
Re: New Engine
« Reply #21 on: May 30, 2015, 02:10:50 AM »
Well I thought the U joint was bad but it seems to be ok. I was getting some vibes at about 45-50 so assumed it went again. Going to try tightening everything up and hope it goes away
Logged
1993 YJ - I6 - 4" RC Lift - 8k Winch - 33's
Pages: 1 [2]   Go Up
« previous next »