« previous next »
Pages: [1]   Go Down

Author Topic: CJ5 D44 Rear  (Read 1348 times)

Offline C-Dawg

  • Trail Passenger
  • *
  • Posts: 2
CJ5 D44 Rear
« on: February 10, 2011, 02:26:43 AM »
I have, for sale, a D44 rear axle from a 1975 CJ5.  I believe it's a 3.73 ratio.  Must be able to pick up.
Logged

Offline Flex

  • Honorary Member
  • Trail Master
  • ***
  • Posts: 772
Re: CJ5 D44 Rear
« Reply #1 on: February 10, 2011, 11:33:58 PM »
How much are you asking for it this would make a great axle swap for someone.
Logged
2000 XJ Sport 6.5 inch TNT Longarms, 36" IROK Radials, HP dana 30, Ford 8.8 aussie locker, 4.10s, front bumper with stinger and 9500 mile maker winch, Rock Sliders, OBA. full exo cage, chopped.
2005 F-150

-Nate

Offline C-Dawg

  • Trail Passenger
  • *
  • Posts: 2
Re: CJ5 D44 Rear
« Reply #2 on: February 11, 2011, 01:58:36 AM »
$250.00
Logged

Offline zjchef25

  • Rock Crawler
  • ****
  • Posts: 358
Re: CJ5 D44 Rear
« Reply #3 on: February 11, 2011, 02:24:38 AM »
would it work for me nate?
Logged

Offline gearhead1985B

  • Honorary Member
  • Trail Master
  • ***
  • Posts: 882
  • the Snozberries taste like Snozberries
Re: CJ5 D44 Rear
« Reply #4 on: February 11, 2011, 03:24:39 AM »
i think the width will be off i am pretty sure the cj5's are alot narrower than a zj rear axle
Logged
"If you can read this, Thank a Teacher, if you can read it in English, thank a SOLDIER"

https://www.masterpull.com/Index.aspx
http://www.taboocustoms.com/

Offline Flex

  • Honorary Member
  • Trail Master
  • ***
  • Posts: 772
Re: CJ5 D44 Rear
« Reply #5 on: February 11, 2011, 04:46:31 AM »
Quote from: zjchef25 on February 11, 2011, 02:24:38 AM
would it work for me nate?

not sure do some research
Logged
2000 XJ Sport 6.5 inch TNT Longarms, 36" IROK Radials, HP dana 30, Ford 8.8 aussie locker, 4.10s, front bumper with stinger and 9500 mile maker winch, Rock Sliders, OBA. full exo cage, chopped.
2005 F-150

-Nate

Offline zjchef25

  • Rock Crawler
  • ****
  • Posts: 358
Re: CJ5 D44 Rear
« Reply #6 on: February 11, 2011, 02:04:26 PM »
to lazy... lol
Logged

Offline Bill3753

  • Honorary Member
  • Rock Crawler
  • ***
  • Posts: 476
Re: CJ5 D44 Rear
« Reply #7 on: February 11, 2011, 07:35:31 PM »
CJ Dana 44's are around 51" WMS to WMS.  Your axles are just like TJ's, so they should be 61" wide.

Can it work, sure anything can work.  Is it going to be tough to use and adapt for your width, yes.  Don't get me wrong, that is a good axle and a good deal.  It wouldn't be very cost effective to use in a TJ/ZJ though.  The bracket kit alone for it would set you back $250-$350 and then you have to think about a locker too.  Lunch box lockers run roughly $200-$300 depending on the deal you can find.  Then you'll have time in getting it ready.

Just throwing out there a few numbers and things I have learned researching for my build.  You just need to figure out if its worth it to you.

Logged
04 TJ, HP60, 14 Bolt, 5.13's, linked, locked, on 38's and (still) in the works.

Offline calvynandhobbs

  • Honorary Member
  • Trail Master
  • ***
  • Posts: 3087
Re: CJ5 D44 Rear
« Reply #8 on: February 12, 2011, 12:39:29 AM »
You'd be better off buying Steve's D44 that he's selling from his TJ. It's a little more expensive, but much less hassle installing.
Logged
1994 YJ on 37s

Offline footman

  • Honorary Member
  • Trail Master
  • ***
  • Posts: 637
Re: CJ5 D44 Rear
« Reply #9 on: February 12, 2011, 04:38:30 AM »
Entertain me Mike:)
Logged
Pages: [1]   Go Up
« previous next »